The UML management console is a low-level interface to the kernel, somewhat like the i386 SysRq interface. Since there is a full-blown operating system under UML, there is much greater flexibility possible than with the SysRq mechanism.
There are a number of things you can do with the mconsole interface:
You need the mconsole client (uml_mconsole) which is present in CVS (/tools/mconsole) in 2.4.5-9um and later, and will be in the RPM in 2.4.6.
You also need CONFIG_MCONSOLE (under 'General Setup') enabled in UML. When you boot UML, you'll see a line like:
mconsole initialized on /home/jdike/.uml/umlNJ32yL/mconsole
umid=debian
mconsole initialized on /home/jdike/.uml/debian/mconsole
host% uml_mconsole debian
host% uml_mconsole /home/jdike/.uml/debian/mconsole
You'll get a prompt, at which you can run one of these commands:
This takes no arguments. It prints the UML version.
(mconsole) version
OK Linux usermode 2.4.5-9um #1 Wed Jun 20 22:47:08 EDT 2001 i686
There are a couple actual uses for this. It's a simple no-op which can be used to check that a UML is running. It's also a way of sending an interrupt to the UML. This is sometimes useful on SMP hosts, where there's a bug which causes signals to UML to be lost, often causing it to appear to hang. Sending such a UML the mconsole version command is a good way to 'wake it up' before networking has been enabled, as it does not do anything to the function of the UML.
These take no arguments. They shut the machine down immediately, with no syncing of disks and no clean shutdown of userspace. So, they are pretty close to crashing the machine.
(mconsole) halt
OK
"config" adds a new device to the virtual machine or queries the configuration of an existing device.
Currently the ubd and network drivers support pulling devices. It takes one argument, which is the device to add, with the same syntax as the kernel command line.
(mconsole)
config ubd3=/home/jdike/incoming/roots/root_fs_debian22
OK
(mconsole) config eth1=mcast
OK
(mconsole) config ssl0
OK pty:/dev/ptyp0
(mconsole) config ubd0
OK /home/jdike/roots/cow.debian,/home/jdike/roots/debian_22
"remove" deletes a device from the system. Its argument is just the name of the device to be removed. The device must be idle in whatever sense the driver considers necessary. In the case of the ubd driver, the removed block device must not be mounted, swapped on, or otherwise open, and in the case of the network driver, the device must be down.
(mconsole) remove ubd3
OK
(mconsole) remove eth1
OK
This takes one argument, which is a single letter. It calls the generic kernel's SysRq driver, which does whatever is called for by that argument. See the SysRq documentation in Documentation/sysrq.txt in your favorite kernel tree to see what letters are valid and what they do.
"help" returns a string listing the valid commands and what each one does.
This invokes the Ctl-Alt-Del action on init. What exactly this ends up doing is up to /etc/inittab. Normally, it reboots the machine. With UML, this is usually not desired, so if a halt would be better, then find the section of inittab that looks like this
# What to do when CTRL-ALT-DEL is pressed.
ca:12345:ctrlaltdel:/sbin/shutdown -t1 -a -r now
This puts the UML in a loop reading mconsole requests until a 'go' mconsole command is recieved. This is very useful for making backups of UML filesystems, as the UML can be stopped, then synced via 'sysrq s', so that everything is written to the filesystem. You can then copy the filesystem and then send the UML 'go' via mconsole.
Note that a UML running with more than one CPU will have problems after you send the 'stop' command, as only one CPU will be held in a mconsole loop and all others will continue as normal. This is a bug, and will be fixed.
This resumes a UML after being paused by a 'stop' command. Note that when the UML has resumed, TCP connections may have timed out and if the UML is paused for a long period of time, crond might go a little crazy, running all the jobs it didn't do earlier.
This takes a string as its argument, and will cause the UML to printk the string so that it ends up in the kernel message log. This is intended for use in honeypots by allowing the UML-specific stuff in the kernel log to be replaced with messages that don't expose the machine as being a UML.
This takes a filename as its argument. It will return the contents of the corresponding /proc file inside the UML. Example:
(mconsole) proc uptime
It is possible to make a backup of a UML's data without shutting it down. The idea is to pause it, make it flush out its data, copy the filesystem to a safe place, and then resume it. This should usually take seconds, while shutting down and rebooting the UML could take minutes. The exact procedure is this:
(mconsole) stop
(mconsole) sysrq s
host% # Copy the UML's filesystem someplace safe
(mconsole) go
By causing UML to flush its data out to disk, the 'sysrq s' will cause the filesystem to be a clean image. Of course, no guarantees are made for process data which hadn't been written back to the kernel, but the filesystem itself won't need an fsck if it's booted.
The mconsole interface also provides a mechanism for processes inside a UML to send messages to an mconsole client on the host. The procedure is this:
mconsole=notify:<bf>socket
There is a demo mconsole notification client in the utilities tarball in mconsole/notify.pl. This is only a demo, and as such, isn't very useful by itself. It should be customized to fit into whatever environment you are setting up.